1785 l60b-sfyh.com

Allen-Bradley 1771-WHF

Allen-Bradley 1771-WHF Hardy Instruments Weigh Scale Module for Allen-Bradley 1771 Universal I/O Chassis (PLC-5 Family Processors), 1-Channel, Input: Up to four (4) 350 Ohm Full Wheatstone Bridge, Strain Gauge Load Sensors/Cells (10 volt excitation)

Allen-Bradley 1771-WHFB

Allen-Bradley 1771-WHFB Hardy Instruments Weigh Scale Module for Allen-Bradley 1771 Universal I/O Chassis (PLC-5 Family Processors), 1-Channel, Input: Up to four (4) 350 Ohm Full Wheatstone Bridge, Strain Gauge Load Sensors/Cells (10 volt excitation)

Allen-Bradley 1771-WI

Allen-Bradley 1771-WI Hardy Instruments Weigh Scale Module for Allen-Bradley 1771 Universal I/O Chassis (PLC-5 Family Processors), 1-Channel, Input: Up to four (4) 350 Ohm Full Wheatstone Bridge, Strain Gauge Load Sensors/Cells (10 volt excitation)

Allen-Bradley 1771-WN

Allen-Bradley 1771-WN Hardy Instruments Weigh Scale Module for Allen-Bradley 1771 Universal I/O Chassis (PLC-5 Family Processors), 1-Channel, Input: Up to four (4) 350 Ohm Full Wheatstone Bridge, Strain Gauge Load Sensors/Cells (10 volt excitation)

Allen-Bradley 1771-CX1

Allen-Bradley 1771-CX1 PLC-5 Family Local I/O Bus Terminator Cable

Allen-Bradley 1771-CX2

Allen-Bradley 1771-CX2 PLC-5 Family Local I/O Bus Terminator Cable

Allen-Bradley 1771-CX5

Allen-Bradley 1771-CX5 PLC-5 Family Local I/O Bus Terminator Cable

Allen-Bradley 1771-NC15

Allen-Bradley 1771-NC15 PLC-5 Family Local I/O Bus Terminator Cable

Allen-Bradley 1771-PT4

Allen-Bradley 1771-RTP1

Allen-Bradley 1771-RTP1 It weighs around 0.6 pounds (0.3 kilograms) with a size of 4.5 x 12.4 x 6.3 inches (115 x 317 x 160 millimeters).

Allen-Bradley 1770-P1

Allen-Bradley 1770-P1 This power supply requires input from either 120V or 220/240V AC. It is factory-shipped for 120V AC operation, with two metal jumpers installed at the input terminals labeled 120V AC (figure 1)

Allen-Bradley 1771-FD2

Allen-Bradley 1771-FD2 1772 PLC-5 System, Fuse Kit fo

Allen-Bradley 1771-P7K

Allen-Bradley 1771-P7K Allen Bradley PLC 5 Power Supply, 120 or 220 Volts AC Nom Input Voltage, 97-132 or 195-264 Volts AC Input Voltage Range, 16 Amperes (at 5 Volts DC) Backplane Output Current, Conformal Coat

Allen-Bradley 1771-RK

Allen-Bradley 1771-RK plastic keys kit can also be used to prevent the wrong kind of module from being installed in a specific keyed I/O chassis slot.

Allen-Bradley 1771-IFE-CC

Allen-Bradley 1771-IFE-CC module can be used with any 1771 I/O chassis. Compatibility and data table use is listed below.

Allen-Bradley 1771-IFF-CC

Allen-Bradley 1771-IFF-CC Contact your nearest Allen-Bradley office for more information about your programmable controllers

Allen-Bradley 1771-OAN-CC

Allen-Bradley 1771-OAN-CC chassis or a later version of this chassis, and it supports 1-slot addressing with restrictions or half-slot addressing with no restrictions.

Allen-Bradley 1771-OD-CC

Allen-Bradley 1771-OD-CC The isolated output module is powered by the power supply connected to the I/O chassis backplane. The module requires a maximum current of 225mA from the +5V dc output of this supply. Total the current requirements of this module with the other modules in the I/O chassis to avoid overloading the supply or the I/O chassis backplane.