UTS International Co., Ltd-sfyh.com

Sharp Edge Tester T001

T001 Sharp edge tester is used to determine whether the accessible edges on child-related products are likely to cause potential risk of injury after normal use and reasonable abuse. Those child-related products include metal or glass edges on toys and other articles intended for use by children under 8 years of age.

Small Part Cylinder T003

To determine whether child-related products & other articles intended for use by children under 3 years old have potential hazards of choking, suffocate, suction, swallow, etc. If any objects can fit completely into the cylinder without compressing & in any orientation, it is defined as a “Small Part”. Its internal dimensions simulate the fully expanded throat of a child under 3 years old.

Sharp Point Tester T004

Sharp point tester is to determine whether accessible sharp points on child-related products are likely to cause injury. If the accessible sharp point penetrates a specified depth into the small rectangular opening of the tester, the LED is illuminated to indicate that the point is unacceptably sharp.

Mouth Actuated Toy Tester T005

Used to test the safety of the Mouth-Actuated Toys, such as whistles with a ball, the sounders with a reed and other toys. Load the mouth-actuated projectile toy with the intended projectile and apply a pressure of 13,8 kPa ± 5 % in the direction of the mouthpiece for 5 s. Carry out the test 10 times in total.

Accessibility Probe T006

Accessibility Probe is used to assess the surface or components (points and surface of toys) of toys is likely to be touched and lead to hazardous. If the probe contacts the part or component, the part or component is considered to be accessible. Therefore, to do related tests based on standards to decrease hazards for children. This tools are including 2 parts: Probe A and Probe B. An accessible point for a toy or article intended for children 3 years of age or less is one that can be contacted by any portion forward of the collar of the accessibility probe designated as Probe A . An accessible point for a toy or article intended for children over 3 years of age is one that can be contacted by any portion forward of the collar of the accessibility probe designated as Probe B . An accessible point for a toy or article intended for children of ages spanning both age groups is one that can be contacted by any portion forward of the collar of either Probe A or B.

EN 71-2 Toys Flammability Tester T010

T010 Toys Flammability Tester is to test the flammability property for children toys or toys materials. Including below: 1. Toys to be worn on the head: beards, moustaches, wigs etc. made from hair, pile or material with similar features; moulded and fabric masks; hoods, head-dresses etc.; flowing elements of 2. Toys to be worn on the head, but excluding paper novelty hats of the type usually supplied in party crackers; 3. Toy disguise costumes and toys intended to be worn by a child in play; 4. Toys intended to be entered by a child; 5. Soft-filled toys (animals and dolls etc.) with a piled surface or textile surface.

Kinetic Energy Tester T011

T011 Kinetic Energy Tester is used to test the maximum energy produced from projectile toy shoot bullets or launched bows, so as to evaluate ejection articles will cause injury for children or not.

Toy Dynamic Strength (2m/s) Tester T012

T012 Dynamic Strength & 2m/s Tester is used test dynamic strength for wheeled ride-on toys. Simulate children wheeled ride-on toys vertically crush the inelastic step 50 x 50 mm at the stable speed of 2m/s±0.2/s, and then check the damage degree. This device can be used for children ride-on toys, such as children tricycle, toy bikes, scooters, etc.

Automatic Corrugated Fibreboard Bursting Strength Tester A001

A001Automatic Corrugated Fibreboard Bursting Strength Tester is used to test the bursting resistance strength property for corrugated fibreboard, corrugated case. Applicable for paperboard production enterprises, carton production enterprises, cartons use enterprises, scientific research institutions, etc.

COBB Cobb Absorption Tester A003A

To determine the water absorptiveness of sized paper and board, including corrugated fiberboard, under standard conditions. It may not suitable for paper of grammage less than 50g/m2 or embossed paper. It is not suitable for porous papers such as newsprint or unsized papers such as blotting paper or other papers having a relatively high water absorptivenss for which ISO 8787 is more suitable. This instrument is only capable of testing surface water absorption of paper and board. It is not applicable to exactly evaluate the writing performance of paper and board.

COBB Absorption Cutter A003B

This device is a necessary sampler of absorption test, it is an ideal test apparatus of the corrugated board and carton production, research and quality supervision, inspection and other departments. It is suitable for short fiber thinner paper sampling.

Paper Thickness Tester A007B

Paper thickness tester is to test thickness of paper and board, test films, mica plate, etc .

Paper Ash Tester A008

To determine the ash content of the material.

Paper and Board Folding Tester A010

Paper folding tester is used to test folding time of paper, it can also be used to test other materails that need to have endure folding function, such as case board, craft paper, paperboard, corrugated paper grey paper.

Slice Materials Air Permeability Tester( Schopper method ) A013

Air permeance tester is used to test air permeance performance of all kinds of slice materials, such as textiles, films, paper, nonwowens, filter materials ,and so on. this tester is control by single chip microcomputer, and can automatic work, is an advanced equipment for paper industry, textiles industry, and leader industry.

Paper Tensile Strength Tester A014B

To determine tensile strength, peel strength, deformation rate, tear strength, puncture power, heat seal strength, low unwind force and other performance for paper, plastic films, bag, plastic products,laminated films and other sticky materials. Electric power tensile tester can be customized based on different test grips to meet various tension and compression tests. Rally stepless unique features to meet the speed requirements for different tests.

Crush Tester A015

Crush tester is designed to test Ring Crush Test (RCT), Edge Crush Test (ECT). Flat Crush Test (FCT), Pin Adhesion Test(PAT) and Concora Medium Test(CMT). It’s a basic equipment to test the crushing strength for various papers, including corrugated board, tubes, paper and plastics.

Needle Flame Tester TF02

Needle flame tester is made based on standards IEC60695, GB5169. Mainly used to simulate products internal generates small flame under the breakdown situation, and assess its ignition hazard. Applicable for testing flammability of electronic electrical equipment and its components and elements, solid electrical insulation or other combustible materials. Needle flame test method can be used for the situation when small parts or component are not suitable to do glow wire test or horizontal vertical combustion test method.

Horizontal Thrust Tester UTS-TS01

To assess the stability property for activity toys(such as climbing rack, swing, etc) with a free height of fall of 600 mm or less.

Guardrails And Armrest Dynamic Strength Tester TS02

To determine the dynamic strength for barriers and handrails.

Simulation Head Tester TS03

Test for head and neck entrapment.

Probe V TS04

Test template D for assessment of head and neck entrapment in partially bound and V-shaped openings

Swing Suspension Connector Durability Tester TS11

Durability test for suspension connectors and means of suspension.

Glow Wire Tester TF01

Glow wire tester is to assess the fire hazard affected by thermal stress which is generated from the heat source of glow-wire component or overload resistance within short time. Widely applicable for testing fire hazard test for electrical and electronic products, household appliances and their materials, also non-flame ignition test, so as to determine the related materials’ glow wire ignition temperature, flammability and flammability index.

Steel Ball Impact Tester T028

Steel ball impact tester is to test the impact resistance for all rigid toys which cover face including space helmets, goggles or face shields. Based on standard requirements, after testing, toys shall not produce sharp edges, sharp points or loose parts which could enter eyes. If so, then conduct follow tests via sharp edge tester, sharp point tester and small part cylinder.

Impact Hammer T062

Impact test hammer is used to check the mechanical shock resistance of enclosures(appliances shell) for electrical appliances of other electronic products. If damage occurs from the spring operated impact test. The spring operated impact test hammer simulates the mechanical impact to which electrical equipment may be subjected. This impact test hammer is mainly used to test household and similar electrical appliances shell, lever, handle, knobs, lights and other shell to withstand mechanical shocks.The impact tester made of stainless steel or alloy.

Surface Flash Tester T013

To determine the flammability property for fluff or fur fabrics (except floor coverings).

Horizontal and Vertical Flammability Tester TF03

Horizontal and vertical flammability tester is applicable to solid and celluar materials that have an apparent density of not less than 250kg/m3, determined in accordance with ISO 845. And plastic materials used in consumer electric devices and appliances.

Tracking Index Test Equipment TF04

Lighting equipment, low-voltage electrical appliances, household appliances, machine tool electrical appliances, motor, electric tools, electronic equipment, electrical instruments, information technology equipment, insulation materials, engineering plastics industry, electrical fittings, auxiliary parts.

EN Drop Floor T035A

Drop Floor is to determine the toys fall on the floor under a specify height and drop times, and then check if toys produce accessible small parts, hazardous sharp edges, hazardous sharp point or hazardous driven construction, etc.

Ball Pressure Tester TE04

Ball pressure test device is use for heat resistance test to verify the heat resistant performance of insulating material covers and outer parts of the electric appliance .

Paper and Board Smoothness Tester(Bekk Method) UTS-AD12

UTS-AD12 Paper and Board Smoothness Tester(Bekk Method) is used to test smoothness of paper and board, it is according to the international principle of Bekk mathod, it can be used for paper making company, printing company, quality supervision department, universities, and so on .

Internal Bonding Strength- Scott Type A031

To determine the internal bond strength for various paper and board materials according to TAPPI T 569.

Company profile

All products